Features |
Micron® 16nm MLC NAND Flash |
SATA 6 Gb/s interface |
ATA modes supported |
PIO mode 3, 4 |
Multiword DMA mode 0, 1, 2 |
Ultra DMA mode 0, 1, 2, 3, 4, 5, 6 |
512-byte sector size support |
Hot-plug capable |
Native command queuing support with 32-command slot support |
ATA-8 ACS2 command set compliant |
ATA security feature command set and password login support |
Security erase command set: fast and secure erase |
120GB performance (steady state) |
Sequential 128KB read/write: 420/170 MB/s |
Random 4KB read/write: 63,000/12,000 IOPS |
READ/WRITE latency: 0.50/3.0ms (TYP) |
240GB performance (steady state) |
Sequential 128KB read/write: 420/290 MB/s |
Random 4KB read/write: 63,000/18,000 IOPS |
READ/WRITE latency: 0.50/2.0ms (TYP) |
480GB performance (steady state) |
Sequential 128KB read/write: 420/380 MB/s |
Random 4KB read/write: 63,000/23,000 IOPS |
READ/WRITE latency: 0.50/2.0ms (TYP) |
600GB performance (steady state) |
Sequential 128KB read/write: 420/380 MB/s |
Random 4KB read/write: 65,000/40,000 IOPS |
READ/WRITE latency: 0.50/1.0ms (TYP) |
800GB performance (steady state) |
Sequential 128KB read/write: 420/380 MB/s |
Random 4KB read/write: 65,000/30,000 IOPS |
READ/WRITE latency: 0.50/1.5ms (TYP) |
960GB performance (steady state) |
Sequential 128KB read/write: 420/380 MB/s |
Random 4KB read/write: 65,000/10,500 IOPS |
READ/WRITE latency: 0.50/3.0ms (TYP) |
Reliability |
MTTF: 2.0 million device hours |
Static and dynamic wear leveling |
Uncorrectable bit error rate (UBER): <1 sector per 1016 bits read |
End-to-end data protection |
Enhanced power-loss data protection with data protection capacitor monitoring |
Self-monitoring, analysis, and reporting technology (SMART) command set |
Endurance: Total bytes written (TBW) |
120GB: 460TB; 240GB: 920TB; 480GB: 1850TB; 600GB: 3800TB; 800GB: 2500TB; 960GB: 1140TB |
Capacity (unformatted): 120GB, 240GB, 480GB, 600GB, 800GB, 960GB |
Mechanical: 7.0mm height |
SATA connector: 5V ±10% |
2.5-inch drive: 100.45mm x 69.85mm x 7.0mm |
Conforms to SFF standards |
RoHS-compliant package |
Field-upgradeable firmware |
Power consumption: <6.0W (TYP); <6.3W (TYP) for 600GB/800GB/960GB |
Operating temperature |
Commercial (0°C to 70°C) |
|
Part Numbering Information |
This device is available in different configurations and densities. Visit micron.com for a list of valid part numbers. |
General Description |
Micron’s M510DC solid state drive (SSD) uses a single-chip controller with a SATA interface on the system side and n-channels of Micron NAND Flash internally. Packaged in an HDD replacement enclosure, the SSD integrates easily in existing storage infrastructures. |
|
Logical Block Address Configuration |
The drive is set to report the number of logical block addresses (LBA) that will ensure sufficient storage space for the specified density. Standard LBA settings, based on the IDEMA standard (LBA1-02), are shown below. |
Table 1. Standard LBA Settings – 512-Byte Sector Size Drive Size | Total LBA | Max LBA | User Available Bytes | Decimal | Hexadecimal | Decimal | Hexadecimal | (Unformatted) | 480GB | 937,703,088 | 37E436B0 | 937,703,087 | 37E436AF | 480,103,981,056 |
|
Products and specifications discussed herein are subject to change by Micron without notice. This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein. Although considered final, these specifications are subject to change, as further product development and data characterization sometimes occur. |