Micron M510DC , 120GB, SATA 6Gb/s, 16nm MLC 2.5" 7mm, 1DWPD

Features

Micron^® 16nm MLC NAND Flash

SATA 6 Gb/s interface

ATA modes supported

PIO mode 3, 4

Multiword DMA mode 0, 1, 2

Ultra DMA mode 0, 1, 2, 3, 4, 5, 6

512-byte sector size support

Hot-plug capable

Native command queuing support with 32-command slot support

ATA-8 ACS2 command set compliant

ATA security feature command set and password login support

Security erase command set: fast and secure erase

120GB performance (steady state)

Sequential 128KB read/write: 420/170 MB/s

Random 4KB read/write: 63,000/12,000 IOPS

READ/WRITE latency: 0.50/3.0ms (TYP)

240GB performance (steady state)

Sequential 128KB read/write: 420/290 MB/s

Random 4KB read/write: 63,000/18,000 IOPS

READ/WRITE latency: 0.50/2.0ms (TYP)

480GB performance (steady state)

Sequential 128KB read/write: 420/380 MB/s

Random 4KB read/write: 63,000/23,000 IOPS

READ/WRITE latency: 0.50/2.0ms (TYP)

600GB performance (steady state)

Sequential 128KB read/write: 420/380 MB/s

Random 4KB read/write: 65,000/40,000 IOPS

READ/WRITE latency: 0.50/1.0ms (TYP)

800GB performance (steady state)

Sequential 128KB read/write: 420/380 MB/s

Random 4KB read/write: 65,000/30,000 IOPS

READ/WRITE latency: 0.50/1.5ms (TYP)

960GB performance (steady state)

Sequential 128KB read/write: 420/380 MB/s

Random 4KB read/write: 65,000/10,500 IOPS

READ/WRITE latency: 0.50/3.0ms (TYP)

Reliability

MTTF: 2.0 million device hours

Static and dynamic wear leveling

Uncorrectable bit error rate (UBER): <1 sector per 10¹⁶ bits read

End-to-end data protection

Enhanced power-loss data protection with data protection capacitor monitoring

Self-monitoring, analysis, and reporting technology (SMART) command set

Endurance: Total bytes written (TBW)

120GB: 460TB; 240GB: 920TB; 480GB: 1850TB; 600GB: 3800TB; 800GB: 2500TB; 960GB: 1140TB

Capacity (unformatted): 120GB, 240GB, 480GB, 600GB, 800GB, 960GB

Mechanical: 7.0mm height

SATA connector: 5V ±10%

2.5-inch drive: 100.45mm x 69.85mm x 7.0mm

Conforms to SFF standards

RoHS-compliant package

Field-upgradeable firmware

Power consumption: <6.0W (TYP); <6.3W (TYP) for 600GB/800GB/960GB

Operating temperature

Commercial (0°C to 70°C)

Part Numbering Information

This device is available in different configurations and densities. Visit micron.com for a list of valid part numbers.

General Description

Micron’s M510DC solid state drive (SSD) uses a single-chip controller with a SATA interface on the system side and n-channels of Micron NAND Flash internally. Packaged in an HDD replacement enclosure, the SSD integrates easily in existing storage infrastructures.

Logical Block Address Configuration

The drive is set to report the number of logical block addresses (LBA) that will ensure sufficient storage space for the specified density. Standard LBA settings, based on the IDEMA standard (LBA1-02), are shown below.

Table 1. Standard LBA Settings – 512-Byte Sector Size

Products and specifications discussed herein are subject to change by Micron without notice. This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein. Although considered final, these specifications are subject to change, as further product development and data characterization sometimes occur.